Відео

are those intake manifold linkages stock 😅

Don't drill the rivets. Jesus. Just disassemble the console and do a proper paint job. Lol.

I have a no crank no start on a 2014 accent. It has new crank position sensor,new battery and new low fuel pump. What’s the first sign of bad starter?

Hey quest do I need to remove the valve covers in order to get the intake out

Hello man thanks for video I have a question about audi a8 d3, there are many mistake lights on control panel like as abs esp and big attention sign. But no sign of malfunction because car is move good, how can I fix and delete this mistakes and what should I do

HI I NEED TO MAKE 4 PORT FEUL PRESSURE REGULATOR/DAMPER TUTORIAL

No focus on the switch on the actuator

Best educational video I’ve seen on that particular job on a 4.0. Thank you very much sir!!

Useless ass video bro

Can you even buy that USC paint stripper anymore?

Is the hoses the same for the lbz2007

bro great job but what accent is that?

Great video, thanks a lot. I received two bags from China, it seems all the top seals are included. What are the set of keys you have at 5:43 to release the connector? Thanks again!

25:48 ok! Donc faire la distribution sans respecter la procédure, engendre une forte consommation de carburant !!! Big merci à toi mon frère ! Car j’ai, justement, une forte consommation d’essence. Et je vais y remédier grâce à toi🙏😉

10:35 clik clik clik au démarrage… c’est à cause du tendeur de chaînes d’arbres à cames !!! Ok ok. Merci beaucoup. Mais après avoir remplacé les tendeurs de chaînes d’arbres à cames, comment remettre les arbres à cames en place bien orienté? (bien caler, bien droit. Est-ce qu’il y à un repère, ou une encoche , Ou quelques choses pour indiquer le bon emplacement ?)

What's the paint color for the speaker grills? I want to repaint mines and your color is the same as mine

There ias no need for any seel on the shaft , centifugal force of the spinning prevents any leakage along the shaft , I know what you are doing is well intentioned but it will not make the slightest difference . How do i know this; I am a time served heating engineer.

This video is like some one goes to the repair shop have the work done and ask for the old parts and make a video and show no work (the car looks great)

I have the same snd woring done , but now become worest

Is age or mileage more important when determining whether a timing belt is still good? My A8 only has 50k kms added since the timing belt was replaced but the belt was replaced but it was replaced almost 12 years ago. I'm going to be replacing the belt anyways just to be safe but what do you think?

Is the distribution the same, for the Audi 3.7l v8 2004 280hp please? (Clamping torce, same camshaft setting bar, pige ect...)

Est-ce que c’est pareil la distribution, pour la Audi 3.7l v8 2004 280ch svp? (Couple de serrage, même barre de calage arbres à cames, pige ect… )

Yeah what if the whole sides and roof part are completely gone rusted is it still possible to just cover everything in bondo and sand it and sculpt it to the original form? It would be hard as fuck because it has to be perfect for the door seals and the windshield gasket to fit

So your purge valve was leaking air into the system but had no fuel leaks ?

Thank you ,, good job

I have issue at abs still even I make the wiring

Mine is throwing p0193 fuel rail pressure low during power enrichment, only does it while towing on a steep grade. Things I've done New cp3 Filter housing rebuild New fuel filter Ppe race plug New fuel lines inside engine bay Any help is appreciated please

That multi tool your using fives off the impression that you're a butcher. As if that wasnt bad enough i had to watch you slop glue all over the place. This review is for anyone thinking this work is the standard practice for this repair. Its not

Bay weip saet address

How did you do that change on yours i have the same model and need to find out how to in stall them

I was on the fence about buying one. Thanks for confirming how good it is, I'll definitely get one !

from Quebec? Im just inspecting my 2009 toyota corrola for rust around the top of the roof near the windshield... my problem is my windshield is in good shape... pulling it out and putting it back is out of my skill set... i might need to get this done by a carrosie

Do they smoke when driven at high temperature?

Does the A8 2008 4,2 gasoline also have belt?

What tools are needed for the job

Hey buddy my name is Patrick an I'm doing the same swap on my 03 Duramax an I would like to ask you a couple of questions if you don't mind I took the wires out of the doner harness that needed an installed them into my factory harness pin for pin the only wires i have left over that are not hooked up are a pink wire, yellow an brown with a white stripe that went to the doner harness at the left front kick panel plug do I need to splice them into my factory harness or are they not used also everything works other than my heated seats on both sides im not sure what to do any help would be much appreciated!

Hey man same problem here. Brake works just fine when I pull it and push it but somehow it beeps all the time as if it is still on while none of the brakes are active. Driving became hell and I am not able to go to a mechanic . I am thinking of cutting off the EPB fuses just so this annoyimg sound goes away. I dont need handbrakes either. What would you say?

What did you use to cut

I thought the 4.2 had a timing chain, in the rear of the motor?

Thanks so much for posting these! Recently grabbed a 447 I'm about to tear into.

What size of hose did you use ? My truck is having the same symptoms

Does anyone know what the purple and brown connection are for that go to the BCM and fuse panel? Just installed a donor harness that didn't have these but had factory heated seats. Wondering if all I need know is a factory door switch to turn the seats on? Do I need those two plugs for the heated seats to work? Any help is greatly appreciated.

I make them out of old washers. Basically the same as you did. 👍

Thanks for this Veikra. Very helpful. What make of hub did you use? Is MOOG a dependable brand? I also have to replace the lower and upper arms. All bushing is shot. Thanks again.

Any tips on cv axle shield rounded out bolt???

Every upload makes me happy. There is rarely and video on a8 d3 gen in usa at least... thank you for providing these informations.

Great video! Thanks for sharing!

Update. I have now blown the new unit I got after this one. Same thing, the output shaft is wallowed out and moves sideway and ate the seal !

hey dude is there anything to look out for when replacing the entire motor with a new one?

Hey man I have the same compressor and I’m trying to change the valves do you no if there is 4 bigger valves and 3 smaller valves ?